Technical-Bulletin-Kyocera-SB-3AX

TECHNICAL BULLETIN TB No.: 3AX-004 Date: 15 / 01 / 2001 4526 MODEL: M-2107 (M-2007) SUBJECT: Parts use for the M-2007 and M-2107 The production of the M-2107 (mail box) for the KM-6230 started in August, 2000. Some parts were newly added and changed on the M-2107, compared to the M-2007; option for the Vi 230 / 310 L. The ‘MOUNT, SOLENOID’, ‘LEVER, ADMISSION SOLENOID’ and the ‘IC, MAIN PCB (CPU)’ ( or the PARTS PCB BOX ASS’Y ) can in principal be used for both the M-2107 and the M-2007. However, only the ‘old’ parts can be used on the M-2007 and the new parts can only be used on the M-2107. Please refer to the parts table on page 2. Please mind that the new parts mentioned in the drawing below cannot be used on the M-2007, since the control of the solenoid has been added and the software of the ‘IC, MAIN PCB (CPU)’ has been modified especially for the M-2107. Caution point when replacing the solenoid When installing the solenoid, it is necessary to attach the ‘SPACER, FEED IN SOLENOID’ (clear resin / transparant plastic) and to bring it close to the paper ejection side so that the ‘SPRING PIN’ does not catch between the ‘LEVER, ADDMISSION SOLENOID’ and the ‘SPACER, FEED IN SOLENOID nor become locked in between. ‘SPACER, FEED IN SOLENOID’ (transparant plastic) ‘PIN, CONNECTOR’ ‘SPRING B, SAFETY SWITCH’ ‘LEVER, ADDMISSION SOLENOID’ SPRING PIN 2 × 12 ‘MOUNT, SOLENOID’ Screw: M3 × 5 ‘SOLENOID, STOPPER’ Paper ejection side Fix the solenoid with two screws(M3 × 5) from the mount side. 1 / 2
Page 1 of 2

Compatible Models: Kyocera-SB-3AX.
– Kyocera-SB-3AX Technical-Bulletin: is a handbook published by Kyocera manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Kyocera-SB-3AX Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Kyocera-SB-3AX Technical-Bulletin:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Kyocera-SB-3AX Technical-Bulletin.
1.3 Diagnostic all errors are generated by Kyocera-SB-3AX Technical-Bulletin:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Kyocera-SB-3AX.
1.5 How to update firmware Kyocera-SB-3AX.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Kyocera-SB-3AX: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Kyocera-SB-3AX.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Kyocera-SB-3AX Technical-Bulletin covers following topics:

– Precautions Kyocera-SB-3AX.
– Product Specification Kyocera-SB-3AX.
– System Overview Kyocera-SB-3AX.
– S/W Structure and Descriptions Kyocera-SB-3AX.
– Disassembly and Reassembly Kyocera-SB-3AX.
– Alignment and Adjustments Kyocera-SB-3AX.
– Troubleshooting Kyocera-SB-3AX.
– Exploded Views & Parts List Kyocera-SB-3AX.

Free Download Kyocera-SB-3AX Technical-Bulletin

Kyocera-SB-3AX Technical-Bulletin

Leave a Reply