Service-Info-Kyocera-FS-8000C

Service info. PI-002 Product: FS-8000C SUBJ.: UP-GRADE PF-30, ST-30, SO-30 AND DF-31 IN ORDER TO LET THEM WORK WITH FS-8000C 1. TECHNICAL EXPLANATION 1-1 PF-30 It is necessary to exchange one Gear and its mounting bracket, in order to up grade PF-30 to PF-30A. Then PF-30A can work with FS-8000C and of course with FS-9000, FS-7000+ and FS-7000. [NOTE] Since December 2000, only PF-30A is being produced at Manufacture side (No need to Up-grade) 1-2 ST-30, SO-30, DF-31 It is necessary to Up-date EP-ROM version of ST-30, SO-30 and DF-31, in order to make them possible to work with FS-8000C. After up dating EP-ROM, all those 3 options can work with FS-8000C and of course with FS-9000, FS-7000+ and FS-7000. [NOTE] Since following production date of each option, new EP-ROM had been implemented at Manufacture side. (No need to Up-grade) >ST-30: August 2001 and onwards >SO-30: August 2001 and onwards >DF-31: October 2001 and onwards 2. UP-GRADE KIT Following 4 UP-GRADE KIT is necessary to Up-grade each option. >> UP-GRADE KIT for PF-30 >> UP-GRADE KIT for ST-30 >> UP-GRADE KIT for SO-30 >> UP-GRADE KIT for DF-31 3. Contents of each UP-GRADE KIT >>UP-GRADE KIT for PF-30 a) 1x Gear b) 1x Gear mounting bracket c) 1x E-ring d) 1x Screw >>UP-GRADE KIT for ST-30 a) 1x EP-ROM b) 2x Joint Brackets c) 1x New Installation Guide of ST-30 >>UP-GRADE KIT for SO-30 a) 1x EP-ROM b) 1x New Installation Guide of SO-30 >>UP-GRADE KIT for DF-31 a) 1x EP-ROM b) 2x Joint Brackets c) 1x Ferrite core d) 1x New Installation Guide of DF-31 4. How to exchange the Gear and EP-ROM Please refer supplement information in following pages. [NOTE] Only DF-31 needs to be done the Home position alignment after exchanging EP- ROM. Please refer supplement information of DF-31. 1/1 ISSUE DATE: 06.12.2001
Page 1 of 8

Compatible Models: Kyocera-FS-8000C.
– Kyocera-FS-8000C Service-Bulletin: is a handbook published by Kyocera manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Kyocera-FS-8000C Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Kyocera-FS-8000C Service-Bulletin:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Kyocera-FS-8000C Service-Bulletin.
1.3 Diagnostic all errors are generated by Kyocera-FS-8000C Service-Bulletin:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Kyocera-FS-8000C.
1.5 How to update firmware Kyocera-FS-8000C.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Kyocera-FS-8000C: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Kyocera-FS-8000C.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Kyocera-FS-8000C Service-Bulletin covers following topics:

– Precautions Kyocera-FS-8000C.
– Product Specification Kyocera-FS-8000C.
– System Overview Kyocera-FS-8000C.
– S/W Structure and Descriptions Kyocera-FS-8000C.
– Disassembly and Reassembly Kyocera-FS-8000C.
– Alignment and Adjustments Kyocera-FS-8000C.
– Troubleshooting Kyocera-FS-8000C.
– Exploded Views & Parts List Kyocera-FS-8000C.

Free Download Kyocera-FS-8000C Service-Bulletin

Kyocera-FS-8000C Service-Bulletin

Leave a Reply