Service-Bulletin-Kyocera-SRDF-2

SB Number: SB 2BF-013 Creation Date: 19/08/2005 Subject: Model: Measures against DRUM COUPLING coming off FS-C8026N, KM-C2630/C2630D Service Bulletin KIMS Service Team, Kyocera Mita Europe 7096 / SB 2BF-013 Phenomenon: There is a possibility that drum coupling might come off the drum motor pin (which transfers drive from the drum motor to the drum) and ‘unsuccessful color registration’ or ‘Imaging Unit lock’ might occur. Cause: The COVER INNER FRONT is originally supposed to be fastened with M4X10S tight screw (P/N: B1A54100). However, if it is fixed with M4X8S tight screw by mistake, it’s likely to move to the front of machine inside of the front cover. This will result in a decrease of pressure pushing the drum unit to the back of the machine. The lack of pressure will then result in a partial disengagement with the drum motor pin and subsequently the drum coupling is apt to come off. (Please refer to the illustration on the following page for a graphic display of problem location, cause and countermeasure.) Countermeasure: To increase the fixation tolerance of the drum motor pin and drum coupling, T he spring pressure of SPRING JOINT D that pushes JOINT DRUM to the drum coupling side has been increased. Spring pressure: OLD: 6N NEW: 16N No. Old Parts No. New Parts No. 302BG00561 2BG00561 Description Q’ty Interchange ability SP Remarks Old New 1 2BG00560 DRUM DRIVE ASS’Y 4 4 X O O 2 2BG22020 302BG22021 2BG22021 +SPRING JOINT D 4 4 X O - Field Measure: When attaching COVER INNNER FRONT, please be sure to fix right and left side of the cover with M4x10S tight screw (P/N: B1A54100). Affected Machine Serial Numbers: FS-C8026N General: Other specification: From first mass production and after; From the next production and after; KM-C2630/C2630D: From V3006701 and higher.
Page 1 of 38

Compatible Models: Kyocera-SRDF-2.
– Kyocera-SRDF-2 Service-Bulletin: is a handbook published by Kyocera manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Kyocera-SRDF-2 Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Kyocera-SRDF-2 Service-Bulletin:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Kyocera-SRDF-2 Service-Bulletin.
1.3 Diagnostic all errors are generated by Kyocera-SRDF-2 Service-Bulletin:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Kyocera-SRDF-2.
1.5 How to update firmware Kyocera-SRDF-2.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Kyocera-SRDF-2: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Kyocera-SRDF-2.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Kyocera-SRDF-2 Service-Bulletin covers following topics:

– Precautions Kyocera-SRDF-2.
– Product Specification Kyocera-SRDF-2.
– System Overview Kyocera-SRDF-2.
– S/W Structure and Descriptions Kyocera-SRDF-2.
– Disassembly and Reassembly Kyocera-SRDF-2.
– Alignment and Adjustments Kyocera-SRDF-2.
– Troubleshooting Kyocera-SRDF-2.
– Exploded Views & Parts List Kyocera-SRDF-2.

Free Download Kyocera-SRDF-2 Service-Bulletin

Kyocera-SRDF-2 Service-Bulletin

Leave a Reply