SB Number: SB 3JV-001 Creation Date: 09/01/2007 Subject: Model: Firmware upgrade, Scan to SMB support KM-6030/8030, Print/Scan System (V), Scan System (G) Service Bulletin KMIS Service Team, Kyocera Mita Europe 7893 / SB 3JV-001 Contents of change Item Scan to SMB support Contents After upgrading the firmware on both the machine and scanner please use sim U512 to turn the SCAN TO SMB function ON (default setting is “OFF”). 1 To enable this functionality, both the firmware of KM- 6030/8030F/W and the SCANNER NIC should be upgraded ( NIC VER 1.4.02 ) 2 Preventing JAM 34 when the paper is conveyed from the MP tray JAM34: Misfeed in registration/ transfer section When the paper is conveyed from the MP tray the actuator of FEED A SW in front of the registration SW turns OFF. In some cases the paper ‘bounces’ and turns the registration SW ON. As a result, there is a chance JAM34 occurrs. CHANGE 50msec (as the waiting time for bouncing process) is added after the FEED A SW turns OFF. When the paper is conveyed from the cassette 2.3.4, there is no waiting time for FEED B SW. Therefore; 50msec is added for the same reason. The latest as of December 2006 Type Program number Check SUM Version MAIN 2FB2910JU FFF7 335 ENGINE 2FB2911JU DFC1 182 LANGUAGE E 2FB29138J 1A39 45 SCANNER NIC F/W NS30V1402 381E 1.4.02 No. Old part number New part number Description Interc abi Old hange lity New Remarks 1 303JR01010 303JR94011 PARTS,PWB SCANNER NIC ASS’Y,SP X O NIC Ver Field measure: Please upgrade the firmware when necessary Machines with the following machine serial numbers (and upwards) are produced with this latest firmware installed: KM-6030: J3011005- KM-8030: H3006575- Scan to SMB support 1. Image send functionality using the SMB protocol 2. Common address book�� enable to register information for up to 10 destinations 3. The option to specify the destination by direct input 4. WebPage function�� register and delete destination information through �AN 5. Simutaneously sending to up to 20 individual destinations When the version of Nic is 1.4.02 (or newer) and enterprise mode (U510) is set to OFF, Scan To SMB (U512) can be turned ON (“enterprise mode” (U510) and “Scan to SMB” (U512) is mutually exclusive, so when U510 is ON, U512 cannot be turned ON). “Scan to SMB”(U512) and “ScanTo FTP” (U511) can be used simultaneously so they can be on simultaneously When U512 is turned ON, “SCAN TO SMB” (SMB transmission) will appear.
Page 1 of 3

Compatible Models: Kyocera-SCanSystemG.
– Kyocera-SCanSystemG Service-Bulletin: is a handbook published by Kyocera manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Kyocera-SCanSystemG Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Kyocera-SCanSystemG Service-Bulletin:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Kyocera-SCanSystemG Service-Bulletin.
1.3 Diagnostic all errors are generated by Kyocera-SCanSystemG Service-Bulletin:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Kyocera-SCanSystemG.
1.5 How to update firmware Kyocera-SCanSystemG.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Kyocera-SCanSystemG: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Kyocera-SCanSystemG.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Kyocera-SCanSystemG Service-Bulletin covers following topics:

– Precautions Kyocera-SCanSystemG.
– Product Specification Kyocera-SCanSystemG.
– System Overview Kyocera-SCanSystemG.
– S/W Structure and Descriptions Kyocera-SCanSystemG.
– Disassembly and Reassembly Kyocera-SCanSystemG.
– Alignment and Adjustments Kyocera-SCanSystemG.
– Troubleshooting Kyocera-SCanSystemG.
– Exploded Views & Parts List Kyocera-SCanSystemG.

Free Download Kyocera-SCanSystemG Service-Bulletin

Kyocera-SCanSystemG Service-Bulletin

Leave a Reply