Service-Bulletin-Kyocera-PF-35

KMIS Service Team, Kyocera Mita Europe 5205 / SB 2A6-017 Service Bulletin SB Number: Subject: Model: SB 2A6-017 Issue Date: 01/11/2002 Installation paper drawers to KM-C830 (J00 after turning main SW off) KM-C830 When installing the paper drawers PF-30 and PF-35 to the KM-C830 under incorrect installation conditions, the following malfunction will occur. Phenomenon If PF-35 is installed as the 1 The PF-35 (250X2) is not equipped with a JAM detection SW at the vertical conveying section while the PF-30 (500X2) is. Thus, please pay attention to following remarks when installing paper drawers to the KM-C830. — The PF-35 (250x2) must be installed as 3rd or 4th drawer! — The PF-30 (500X2) may not be installed as 3rd or 4th drawer, but as 1 CORRECT st and 2 nd drawer, J00 will appear after turning the main switch ON. st and 2 nd drawer! INCORRECT The problem with installing 2 x PF-30’s (500X2)+(500X2) as 3 Although a JAM code will not be displayed after turning main switch on, the paper size will be incorrectly detected for the 3rd and 4th drawer. Refer to overview below. The length of the paper JAM detection sensor compared to the PF-35 sensor is different. Therefore depending on the paper size, paper jams or incorrect paper detection may occur. rd and 4 th drawer. Paper size in the cassette Paper size display on OP. panel Actual paper detection A4 A4 OK A3 B5 NG A4R A3 NG B4R A4R NG B5R A4R NG KM-C830 PF-35 (250x2) PF-30 (500x2) 1st drawer 2nd drawer 3rd drawer 4th drawer KM-C830 PF-30 (500x2) PF-35 (250x2) 1 / 1
Page 1 of 7

Compatible Models: Kyocera-PF-35.
– Kyocera-PF-35 Service-Bulletin: is a handbook published by Kyocera manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Kyocera-PF-35 Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Kyocera-PF-35 Service-Bulletin:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Kyocera-PF-35 Service-Bulletin.
1.3 Diagnostic all errors are generated by Kyocera-PF-35 Service-Bulletin:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Kyocera-PF-35.
1.5 How to update firmware Kyocera-PF-35.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Kyocera-PF-35: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Kyocera-PF-35.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Kyocera-PF-35 Service-Bulletin covers following topics:

– Precautions Kyocera-PF-35.
– Product Specification Kyocera-PF-35.
– System Overview Kyocera-PF-35.
– S/W Structure and Descriptions Kyocera-PF-35.
– Disassembly and Reassembly Kyocera-PF-35.
– Alignment and Adjustments Kyocera-PF-35.
– Troubleshooting Kyocera-PF-35.
– Exploded Views & Parts List Kyocera-PF-35.

Free Download Kyocera-PF-35 Service-Bulletin

Kyocera-PF-35 Service-Bulletin

Leave a Reply