Service-Bulletin-Kyocera-KM-C2520-3225-3232

SB Number: SB 2FZ-009 Creation Date: 08/12/2006 Subject: Model: NOTE: installing firmware KM-C2520/C3225/C3232 Service Bulletin KMIS Service Team, Kyocera Mita Europe 7791 / SB 2FZ-009 Please note the following when downloading (changing) firmware in the KM-C2520/C3225/C3232 machines. This information is not mentioned in the Service Manual so you are advised to inform your engineers for future reference. NOTE When changing the firmware in the KM-C2520/3225/3232, after inserting the CF card; turn ON the main switch while pressing the “Job Accounting” and “Interrupt” keys at the same time. In normal operation after the main switch is turned ON the KM-C2520/C3225/C3232 loads each firmware from the printer board and it can recognize CF only once the printer board is stabilized. In other words, it cannot recognize the CF until the printer, including the Engine, is stable. This also means that if the machine cannot be stabilized (*), a firmware change cannot be done. However, by turning ON the power while pressing the “Job Accounting” and the “Interrupt” key at the same time, the CF will be recognized immediately and downloading can start without waiting for the machine to stabilize. It will take about 30 seconds for the actual downloading screen to switch to the screen in which “Firmware downloading….” Is displayed. Please make sure that you do not turn the main power OFF during that time. Additionally, please do not turn the power off during each firmware download. Especially when turning the power OFF during the printer firmware download, please understand that you may not be able to be performed the download again. Should you wish to upgrade the firmware without turning the machine on completely (bringing the fuser up to working temperature etc.) because the machine has a failure or it is new and not yet placed at the customer, please follow these instructions: Open the front cover, place the CF card and then swith the main power ON whilst holding down the “Job Accounting” and the “Interrupt” key. Please make sure that you unplug the main power cord when inserting and removing the CF card (which contains the new firmware).
Page 1 of 74

Compatible Models: Kyocera-KM-C2520-3225-3232.
– Kyocera-KM-C2520-3225-3232 Service-Bulletin: is a handbook published by Kyocera manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Kyocera-KM-C2520-3225-3232 Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Kyocera-KM-C2520-3225-3232 Service-Bulletin:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Kyocera-KM-C2520-3225-3232 Service-Bulletin.
1.3 Diagnostic all errors are generated by Kyocera-KM-C2520-3225-3232 Service-Bulletin:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Kyocera-KM-C2520-3225-3232.
1.5 How to update firmware Kyocera-KM-C2520-3225-3232.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Kyocera-KM-C2520-3225-3232: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Kyocera-KM-C2520-3225-3232.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Kyocera-KM-C2520-3225-3232 Service-Bulletin covers following topics:

– Precautions Kyocera-KM-C2520-3225-3232.
– Product Specification Kyocera-KM-C2520-3225-3232.
– System Overview Kyocera-KM-C2520-3225-3232.
– S/W Structure and Descriptions Kyocera-KM-C2520-3225-3232.
– Disassembly and Reassembly Kyocera-KM-C2520-3225-3232.
– Alignment and Adjustments Kyocera-KM-C2520-3225-3232.
– Troubleshooting Kyocera-KM-C2520-3225-3232.
– Exploded Views & Parts List Kyocera-KM-C2520-3225-3232.

Free Download Kyocera-KM-C2520-3225-3232 Service-Bulletin

Kyocera-KM-C2520-3225-3232 Service-Bulletin

Leave a Reply