Service-Bulletin-Kyocera-KM-6030-8030-1

SB Number: SB 2FB-001 Creation Date: 11/11/2005 Subject: Model: Additional information for service engineers KM-6030/8030 Service Bulletin KIMS Service Team, Kyocera Mita Europe 7240 / SB 2FB-001 Remarks when using cassette one and two Figure 2/page 3 If the media placed in (one of) the two cassette(s) is slightly larger than it should be, please adjust the position of the Front Cursor Deck to fit the right size. Background In terms of specification, the tolerance of paper dimension should be within ± 1mm lengthwise and crosswise (based on Japanese Industrial Standards). Within the limits, performance evaluation of the machine has been made and no particular problems are expected. However, various sorts of paper used in the field might have a dimensional variation. In such cases, if the paper is slightly longer than expected, the force applied by the paper and Cushion Cassette might increase too much. This will result in a possible failure to feed paper. Periodic maintenance (Applying grease to fixing drive gear) Figure 1/page 2 To prevent Fixing drive gear from being worn out, apply grease (M014000080) to exterior of Fixing drive gear, p/n: P014000080, by following the procedure as displayed below (every 500.000 copies). Procedures for applying grease 1) Remove the back cover and the electrical components cover. 2) Pull off both connection cables between the DP (at upper rear of the machine) and main PCB. 3) Remove two screws on the right and left side of the electrical unit. (Open either the right or the left side of the unit to be able to access drive unit). 4) Make sure the gear tooth surface can be seen from the Ø20 hole of ‘fixing drive unit’ plate (located to the right of the toner disposal pipe (1*)). Apply grease to the exterior of ‘fixing drive unit’. (1*) In case of doing this to old plate with no Ø20 hole, remove fixing drive unit and take out <FIXING DRIVE GEAR>,and apply grease up. Remarks when setting up machine (Placing LABEL VFEED CAUTION) When the specified language is not English, please order the following ‘Label vfeed caution 6nations’ which is corresponding each language and select the one meeting that spec and put it on ‘Label vfeed caution’ (p/n: 2FB05380) LABEL VFEED CAUTION 6NATIONS P/N: 2FB05440: 230Vspec except for GEN LABEL VFEED CAUTION 6NATIONS(GE) P/N:2FB43410: GEN spec LABEL VFEED CAUTION P/N: 2FB05380 PUSH COVER VERTICAL FEED P/N: 2FB07500
Page 1 of 46

Compatible Models: Kyocera-KM-6030-8030-1.
– Kyocera-KM-6030-8030-1 Service-Bulletin: is a handbook published by Kyocera manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Kyocera-KM-6030-8030-1 Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Kyocera-KM-6030-8030-1 Service-Bulletin:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Kyocera-KM-6030-8030-1 Service-Bulletin.
1.3 Diagnostic all errors are generated by Kyocera-KM-6030-8030-1 Service-Bulletin:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Kyocera-KM-6030-8030-1.
1.5 How to update firmware Kyocera-KM-6030-8030-1.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Kyocera-KM-6030-8030-1: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Kyocera-KM-6030-8030-1.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Kyocera-KM-6030-8030-1 Service-Bulletin covers following topics:

– Precautions Kyocera-KM-6030-8030-1.
– Product Specification Kyocera-KM-6030-8030-1.
– System Overview Kyocera-KM-6030-8030-1.
– S/W Structure and Descriptions Kyocera-KM-6030-8030-1.
– Disassembly and Reassembly Kyocera-KM-6030-8030-1.
– Alignment and Adjustments Kyocera-KM-6030-8030-1.
– Troubleshooting Kyocera-KM-6030-8030-1.
– Exploded Views & Parts List Kyocera-KM-6030-8030-1.

Free Download Kyocera-KM-6030-8030-1 Service-Bulletin

Kyocera-KM-6030-8030-1 Service-Bulletin

Leave a Reply