Service-Bulletin-Kyocera-KM-1635-2035

SB Number: SB 2C9-031 Creation Date: 03/08/2006 Subject: Model: CAUTION when installing a Paper Feeder KM-1620/2020/1650/2050/2550/1635/2035/PF-410 Service Bulletin KIMS Service Team, Kyocera Mita Europe 7201 / SB 2C9-031 Remarks 1: When (un-)installing the Paper Feeder, please make sure the power plug is removed from the main unit (MFP). Once the power plug is (dis-)connected, please wait more than 10 seconds after the plug is disconnected. There is about 10 seconds between cutting off the input power supply and the point where the 5V/24V ‘power supply PCB’ stops. When an excessive voltage is apply to the MAIN PCB ASSY (3HW0101_) of a paper feeder whilst (un)installing that paper feeder, there is a possibility of damaging the parts. Especially the motor driver IC (U2) is receptive to damage. If it is damaged, the following phenomena might occur: 1) The paper will not be fed from the paper feeder; 2) When the start key is pressed selecting the 3 rd or 4 th paper feeder the following phenomena might occur: the LCD on the operation panel will be off; the machine will restart; C calls (C0420/C0500/C0510) might be indicated. 2: When installing the machine main body on the Paper Feeder, please keep the positioning pin located at back side of the Paper Feeder in mind. Also, be careful to place the machine main body right below the Paper Feeder slowly and quietly. Shock is strictly prohibited! If placing the machine main body on the PF at an angle or by giving a shock, there is a possibility that it will cause damage or deform the positioning pin or the entire drawer. If the connection was incorrect at installation or incomplete after installation, please check if the machine main body and/or drawer have been damaged/deformed, or if foreign particle are in the drawer. Especially if foreign particles are mixed in the drawer electrode section causing a connection failure on the 5V/24V line, the following phenomenon might occur. 1. The Paper Feeder is not recognized; 2. The paper is not being fed from the PF; 3. The motor driver IC (U2) on the Paper Feeder Main PCB Ass’y (3HW0101_) is damaged. Example of a broken connector (located on the machine main body side).
Page 1 of 18

Compatible Models: Kyocera-KM-1635-2035.
– Kyocera-KM-1635-2035 Service-Bulletin: is a handbook published by Kyocera manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Kyocera-KM-1635-2035 Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Kyocera-KM-1635-2035 Service-Bulletin:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Kyocera-KM-1635-2035 Service-Bulletin.
1.3 Diagnostic all errors are generated by Kyocera-KM-1635-2035 Service-Bulletin:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Kyocera-KM-1635-2035.
1.5 How to update firmware Kyocera-KM-1635-2035.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Kyocera-KM-1635-2035: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Kyocera-KM-1635-2035.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Kyocera-KM-1635-2035 Service-Bulletin covers following topics:

– Precautions Kyocera-KM-1635-2035.
– Product Specification Kyocera-KM-1635-2035.
– System Overview Kyocera-KM-1635-2035.
– S/W Structure and Descriptions Kyocera-KM-1635-2035.
– Disassembly and Reassembly Kyocera-KM-1635-2035.
– Alignment and Adjustments Kyocera-KM-1635-2035.
– Troubleshooting Kyocera-KM-1635-2035.
– Exploded Views & Parts List Kyocera-KM-1635-2035.

Free Download Kyocera-KM-1635-2035 Service-Bulletin

Kyocera-KM-1635-2035 Service-Bulletin

Leave a Reply