Service-Bulletin-Kyocera-FS-C8520-C8525MFP

Service Bulletin Subject Measures against Faulty Detection of Cassette Paper Level (Faulty Detection of Paper Empty) FS-C8020MFP, FS-C8025MFP, FS-6025MFP, FS-6025MFP/B, FS-6030MFP, FS-6525MFP, FS-6530MFP, PF-470, PF-471, (TASKalfa 2550ci, PF-790)* *TASKalfa 2550ci and PF-790: Changed for common use of the part Installation target models of PF-470/PF-471: FS-6025MFP, FS-6025MFP/B, FS-6030MFP, FS-C8020MFP, FS-C8025MFP, FS-6525MFP, FS-6530MFP PF-790: TASKalfa 2550ci) Topic The cassette lift plate might be deformed by deterioration and accordingly the paper position might be lowered if the conditions below are met (especially for the main unit cassette). Then, the remaining paper might not reach the remaining paper detection actuator, which caused faulty detection of paper empty. Therefore, the following changes were made. Since some attention is required when replacing the parts, please refer to [Field Measures] below. Conditions - The cassette heater is always ON (influence of heat). - A large stack of maximum size paper is loaded for a prolonged time (influence of roads)s Content of changes No. Details The material of the lift plate was changed for heat resistance. (No.5,No.7) (PC+ABS PC) (*1) change 2 (No.5) due to the change 1) above. The shape of the actuator (No.8) was changed due to the change 1) above. (The new type lift plate is heat-resistant, but less rigid. It may bend and fail to detect paper full. Therefore, it was changed as above.) (*2) (*1) This phenomenon does not occur on the TASKalfa 2550ci and PF-790 since the metal plate under the lift plate has drawing compound. However, the change was also applied for common use of the part. (*2) The actuator was not changed for the FS-C8020MFP, FS-C8025MFP and TASKalfa 2550ci since the shape of the actuator and mechanical structure are different. (Page.1/6) Ref. No. 2K3-0034 (C113) <Date> May 18, 2012 KYOCERA Document Solutions Europe Technical Customer Service Division (TCSD) Model Affected Models Lift plate 1 All models The lift plate was newly set up as service part Except TASKalfa 2550ci, PF-790 Actuator change 3 FS-6025MFP, FS-6025MFP/B, FS-6030MFP, FS-6525MFP, FS-6530MFP, PF-470, PF-471, PF-790 Lift plate (No.5, No.7) Actuator (No.8) <Cassette> The lift plate deforms and the remaining paper sensing range for [Low] may be shifted which causes misdetection of [Empty] <Cross section> Lift plate Actuator
Page 1 of 12

Compatible Models: Kyocera-FS-C8520-C8525MFP.
– Kyocera-FS-C8520-C8525MFP Service-Bulletin: is a handbook published by Kyocera manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Kyocera-FS-C8520-C8525MFP Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Kyocera-FS-C8520-C8525MFP Service-Bulletin:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Kyocera-FS-C8520-C8525MFP Service-Bulletin.
1.3 Diagnostic all errors are generated by Kyocera-FS-C8520-C8525MFP Service-Bulletin:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Kyocera-FS-C8520-C8525MFP.
1.5 How to update firmware Kyocera-FS-C8520-C8525MFP.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Kyocera-FS-C8520-C8525MFP: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Kyocera-FS-C8520-C8525MFP.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Kyocera-FS-C8520-C8525MFP Service-Bulletin covers following topics:

– Precautions Kyocera-FS-C8520-C8525MFP.
– Product Specification Kyocera-FS-C8520-C8525MFP.
– System Overview Kyocera-FS-C8520-C8525MFP.
– S/W Structure and Descriptions Kyocera-FS-C8520-C8525MFP.
– Disassembly and Reassembly Kyocera-FS-C8520-C8525MFP.
– Alignment and Adjustments Kyocera-FS-C8520-C8525MFP.
– Troubleshooting Kyocera-FS-C8520-C8525MFP.
– Exploded Views & Parts List Kyocera-FS-C8520-C8525MFP.

Free Download Kyocera-FS-C8520-C8525MFP Service-Bulletin

Kyocera-FS-C8520-C8525MFP Service-Bulletin

Leave a Reply