SB Number: SB 2HP-001 Creation Date: 29/03/2007 Subject: Model: NOTE: How to resolve a JAM in the conveying section FS-C8100DN Service Bulletin KMIS Service Team, Kyocera Mita Europe 7986 / SB 2HP-001 Depending on the variations in light intensity coming from the light generation section (LED) which is the received by the PI sensor (*) (used in the conveying section), there might be a chance that a JAM occurs in the conveying section. Should this JAM at the conveying section occur (too) often in a particular machine in the field, please follow the checklist below and replace all the related sensors used in the conveying section. checklist 1) Perform maintenance mode U031 (Check conveying switch**) and check the operation of all related sensors The following sensors in their respective machines need checking: - KM-C2520/C3225/C3232,FS-C8100DN: - KM-3050/4050/5050,FS-9130DN,LS/FS-9530DN: FEED1/FEED2/FEED3 2) Should (one of) the sensor(s) not be detected (even when activating the actuator), there is a possibility that the sensor might be causing the problem. Therefore, please replace all the switches. FEED2/FEED3 Field measure: In case JAM at the conveying section occurs, please check the condition based on above and replace related all sensors as a set. * ** KM-C2520/C3225/C3232: KM-3050/4050/5050 : Please see the service manual for U031 (service manual 1-3-1: maintenance mode (3)) SWITCH CONVEYING (302FZ4408_) x 2 Pieces SWITCH CONVEYING (302GR4422_) x 3 Pieces
Page 1 of 34

Compatible Models: Kyocera-FS-C8100DN.
– Kyocera-FS-C8100DN Service-Bulletin: is a handbook published by Kyocera manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Kyocera-FS-C8100DN Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Kyocera-FS-C8100DN Service-Bulletin:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Kyocera-FS-C8100DN Service-Bulletin.
1.3 Diagnostic all errors are generated by Kyocera-FS-C8100DN Service-Bulletin:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Kyocera-FS-C8100DN.
1.5 How to update firmware Kyocera-FS-C8100DN.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Kyocera-FS-C8100DN: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Kyocera-FS-C8100DN.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Kyocera-FS-C8100DN Service-Bulletin covers following topics:

– Precautions Kyocera-FS-C8100DN.
– Product Specification Kyocera-FS-C8100DN.
– System Overview Kyocera-FS-C8100DN.
– S/W Structure and Descriptions Kyocera-FS-C8100DN.
– Disassembly and Reassembly Kyocera-FS-C8100DN.
– Alignment and Adjustments Kyocera-FS-C8100DN.
– Troubleshooting Kyocera-FS-C8100DN.
– Exploded Views & Parts List Kyocera-FS-C8100DN.

Free Download Kyocera-FS-C8100DN Service-Bulletin

Kyocera-FS-C8100DN Service-Bulletin

Leave a Reply