Service-Bulletin-Kyocera-FS-C5350

KMIS Service Department, Kyocera Mita Europe A254-A256-A257 / SB 2HN-013 Service Bulletin Page 1 of 1 SB Number: SB 2HN-013 Creation Date: 30/08/2010 Subject: Model: Firmware upgrade FS-C5100DN/5200DN/5300DN/5350DN/5400DN Classification Field measure When the above mentioned phenomena occur, please upgrade the firmware to the latest version. Entire stock rework In-field modification at next visit No modification necessary In-field modification by case Type FS-C5100DN/5200DN/5300DN/5350DN FS-C5400DN The above mentioned changes have been applied to machines produced after the above mentioned production date/ serial number. Serial number July 2010 production XAC0702533 Serial numbers of affected machines 1 The waste toner may be overfilled in the waste toner conveying unit. The waste toner motor drive may not stop under the following conditions: • Duplex printing. • Paper jam • Waster toner box full is detected. Phenomenon If after a paper jam, the paper size has been changed in the command center, the paper jam detection is cancelled. 2 Cancelation of the paper jam sensing. (FS-C5350DN only) Solution Paper jam is checked only when the paper size is changed after detection. The print start will be delayed with 5 seconds, after the paper feed speed has been changed. (Until the T/C sensor output becomes stable) 3 Added print start delay. (FS-C5350DN only) Type SYSTEM ENGINE SYSTEM ENGINE SYSTEM ENGINE SYSTEM ENGINE SYSTEM ENGINE Program No. 2HN_3000006003 2HL_1000009001 2HN_3000006003 2JC_3F00005002 2HN_3000006003 2HN_1000009001 2K8_3000003008 2K8_1000003001 2HG_3000005017 2HG_1000010001 Check SUM 27e2 41f3 27e2 78d8 27e2 8605 c505 542e 2da9 1518 Version 006.003 009.001 006.003 009.001 006.003 009.001 003.008 003.001 005.017 010.001 Status Date 30/10/2009 29/06/2010 30/10/2009 29/06/2010 30/10/2009 29/06/2010 - 28/06/2010 21/10/2009 29/06/2010 Applicable model FS-C5100DN FS-C5100DN FS-C5200DN FS-C5200DN FS-C5300DN FS-C5300DN FS-C5350DN FS-C5350DN FS-C5400DN FS-C5400DN Firmware
Page 1 of 2

Compatible Models: Kyocera-FS-C5350.
– Kyocera-FS-C5350 Service-Bulletin: is a handbook published by Kyocera manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Kyocera-FS-C5350 Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Kyocera-FS-C5350 Service-Bulletin:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Kyocera-FS-C5350 Service-Bulletin.
1.3 Diagnostic all errors are generated by Kyocera-FS-C5350 Service-Bulletin:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Kyocera-FS-C5350.
1.5 How to update firmware Kyocera-FS-C5350.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Kyocera-FS-C5350: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Kyocera-FS-C5350.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Kyocera-FS-C5350 Service-Bulletin covers following topics:

– Precautions Kyocera-FS-C5350.
– Product Specification Kyocera-FS-C5350.
– System Overview Kyocera-FS-C5350.
– S/W Structure and Descriptions Kyocera-FS-C5350.
– Disassembly and Reassembly Kyocera-FS-C5350.
– Alignment and Adjustments Kyocera-FS-C5350.
– Troubleshooting Kyocera-FS-C5350.
– Exploded Views & Parts List Kyocera-FS-C5350.

Free Download Kyocera-FS-C5350 Service-Bulletin

Kyocera-FS-C5350 Service-Bulletin

Leave a Reply