Service-Bulletin-Kyocera-FS-C2026+-C2126+MFP

Service Bulletin Subject Change of Engagement Mechanism of the Drive Section (Measures against Abnormal Noise) FS-C5150DN, FS-C5250DN, FS-C2026MFP, FS-C2126MFP, FS-C2026MFP+, FS-C2126MFP+, FS-C2526MFP, FS-C2626MFP (Page.1/2) Ref. No. 2KT-0018 (C341) <Date> January 8, 2013 KYOCERA Document Solutions Europe Customer Services & Support Division (CSSD) Model KD C’s Classification Entire Stock Rework In-Field modification by case In-Field modification at next visit No modification necessary Field Measure: Please replace DR-590B with the new one (No.1 or No.2) when the phenomenon described below occurs. Serial Nos. of the Affected Machines: Please refer to the following. Topic In a rare case, if the ribs of the joint gears contact each other when switching to the full-color mode (when engaging the gears), the worm gear might skip the teeth of its opposite gear Z due to the excessive loads applied to the developer drive gears engagement mechanism when the engagement operation momentarily stops, which might cause some abnormal noise. As the countermeasures, the shape of the joint gears was changed as follows in order to reduce the loads applied at gear engagement. Content of Changes The rib shapes at the engagement side of the joint gears ( X , Y ) of the drum/developer drive unit (DR-590B) were partly cut in order to avoid the contact with their surface. [DR-590B] (Unit circled in red line) DR-590B: Motor's side DR-590B: Gear's side Joint gears ( X and Y are inserted into the same shaft): By switching the gear Z by the worm gear when switching to full-color mode, the gear X is shifted to thrust direction to engage the gear Y or to release. (B/W mode: Gear X and Y released, Full-color mode: Gear engaged) Part the teeth skip (Teeth of the gear Z and the worm gear) Worm gear Gear Z (Above is the state of switching to the full-color mode)
Page 1 of 4

Compatible Models: Kyocera-FS-C2026+-C2126+MFP.
– Kyocera-FS-C2026+-C2126+MFP Service-Bulletin: is a handbook published by Kyocera manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Kyocera-FS-C2026+-C2126+MFP Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Kyocera-FS-C2026+-C2126+MFP Service-Bulletin:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Kyocera-FS-C2026+-C2126+MFP Service-Bulletin.
1.3 Diagnostic all errors are generated by Kyocera-FS-C2026+-C2126+MFP Service-Bulletin:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Kyocera-FS-C2026+-C2126+MFP.
1.5 How to update firmware Kyocera-FS-C2026+-C2126+MFP.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Kyocera-FS-C2026+-C2126+MFP: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Kyocera-FS-C2026+-C2126+MFP.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Kyocera-FS-C2026+-C2126+MFP Service-Bulletin covers following topics:

– Precautions Kyocera-FS-C2026+-C2126+MFP.
– Product Specification Kyocera-FS-C2026+-C2126+MFP.
– System Overview Kyocera-FS-C2026+-C2126+MFP.
– S/W Structure and Descriptions Kyocera-FS-C2026+-C2126+MFP.
– Disassembly and Reassembly Kyocera-FS-C2026+-C2126+MFP.
– Alignment and Adjustments Kyocera-FS-C2026+-C2126+MFP.
– Troubleshooting Kyocera-FS-C2026+-C2126+MFP.
– Exploded Views & Parts List Kyocera-FS-C2026+-C2126+MFP.

Free Download Kyocera-FS-C2026+-C2126+MFP Service-Bulletin

Kyocera-FS-C2026+-C2126+MFP Service-Bulletin

Leave a Reply