Service-Bulletin-Kyocera-FaxSystemM

SB Number: SB 3KH-001 Creation Date: 14/11/2006 Subject: Model: Firmware upgrade, Ver. 003.002/002.001 (error C0030/C0070) Fax System (M) Service Bulletin KMIS Service Team, Kyocera Mita Europe 7835 / SB 3KH-001 The firmware is upgraded as follows. Contents of change Item 1 Measures against C0030* error when the HDD is full. Remarks C0030* might sometimes light up. This is caused as follows: The controller removes the images piling up inside the FAX board. If the HDD at the controller side is full, C0030* may light up. 2 Measures against a machine lock while receiving with V.34 When receiving with V.34 is not finished properly, the machine may lock because the internal processing is not done correctly. 3 The transmission protocol data of the protocol list is output as a blank sheet. If turning OFF the power while the controller is receiving protocol list data from the FAX board, the status of data being received is not released (even when turning the power back ON). The result is that the data of the protocol list will be output as a blank sheet. (If this situation occurs, please initialize the FAX board to resolve the problem). 4 C0070** when turn ON the power. 5 Image failure during memory transmission. If data cannot be read during the decoding of image data (which is piled up inside the flash memory of the FAX board), the image failure appears. Therefore, it is corrected. 6 C0030* lights up during memory transmission. *: C0030: ** :C0070 : Fax control PWB system problem) Fax control PWB incompatibility detection problem Type Program number Check SUM Version FAX APL 3KH_5100.003.002 -------- 003.002 FAX BOOT 3KH_5000.002.001 -------- 002.001 Field Measure: When the above mentioned phenomenon occurs, please upgrade the firmware. In doing so, please note that APL and BOOT should be upgraded separately.
Page 1 of 2

Compatible Models: Kyocera-FaxSystemM.
– Kyocera-FaxSystemM Service-Bulletin: is a handbook published by Kyocera manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Kyocera-FaxSystemM Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Kyocera-FaxSystemM Service-Bulletin:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Kyocera-FaxSystemM Service-Bulletin.
1.3 Diagnostic all errors are generated by Kyocera-FaxSystemM Service-Bulletin:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Kyocera-FaxSystemM.
1.5 How to update firmware Kyocera-FaxSystemM.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Kyocera-FaxSystemM: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Kyocera-FaxSystemM.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Kyocera-FaxSystemM Service-Bulletin covers following topics:

– Precautions Kyocera-FaxSystemM.
– Product Specification Kyocera-FaxSystemM.
– System Overview Kyocera-FaxSystemM.
– S/W Structure and Descriptions Kyocera-FaxSystemM.
– Disassembly and Reassembly Kyocera-FaxSystemM.
– Alignment and Adjustments Kyocera-FaxSystemM.
– Troubleshooting Kyocera-FaxSystemM.
– Exploded Views & Parts List Kyocera-FaxSystemM.

Free Download Kyocera-FaxSystemM Service-Bulletin

Kyocera-FaxSystemM Service-Bulletin

Leave a Reply