Service-Bulletin-Kyocera-DF-730

SB Number: SB 3JY-002 Creation Date: 01/06/2007 Subject: Model: Firmware change, new model compatibility chart DF-710/730, DP-710 Service Bulletin KMIS Service Team, Kyocera Mita Europe 8095 / SB 3JY-002 The F/W is changed to support the new models, specifically the KM-C4035E. NOTE: The below table describes the compatibility between current and new machines/accessories. It becomes clear that only the new DF-710/730 and DP-710 are compatible with the new KM-C4035E. The new DF/DP models are compatible with all the current and new colour MFP’s, whereas the current DF/DP rnage will cover all but one model; the KM-C4035E. Compatible with present model Support for new model Main body to which it can be installed KM-C2520/C3225/C3232 KM-C2525E/C3232E KM-C2520/C3225/C3232 KM-C2525E/C3232E/C4035E Label on the outer carton DF-710 DF-730 DP-710 DF-710 DF-730 DP-710 Item code: 1203JY0UN0 1205H10UN0 1203J90KL0 1203JY0U10 1205H10U10 1203J90K10 Related part information No. Old part number New part number Description Q’ty Interc abi Old hange lity New Remarks Old New 1 303JY01022 303JY01023 MIDDLE PWB ASS’Y 1 1 X O F/W VER. 3JY_9600.004.002 2 303JY80014 303JY80015 MAIN PWB ASS’Y WITH SOFTWARE SP 1 1 X O F/W VER. 3JY_9200.006.003 3 303J901011 303J901012 DRIVER PWB ASS’Y 1 1 X O F/W VER. 3J9_9500.004.005 4 305H180020 TBA PBA-CONT-F 1 1 X O F/W VER. 5H1_9200.002.007 Contents of change in firmware Model Item Contents 1 DF-710 DF-730 DP-710 Support for new model (KM-C4035E) Changed to support cycle speed of the KM-C4035E 2 DF-710 The timing of paper holding solenoid has been adjusted In order to reduce the sound of the paper holding lever hitting the main tray, the operation timing of the paper holding solenoid has been changed as follows 3 DF-710 Measure against JAM 88 occurring due to 3 sheets monochrome A4 & 2 staples (JAM88: Main tray eject JAM) There might be the possibility that JAM88 might occur when copying 3 sheets Monochrome A4 copy & 2 staples continuously. Therefore, it is corrected. 4 DP-710 The paper feeding timing at Auto Selection mode has been changed. On the Auto Selection mode, there is a possibility that small size original is detected as large size original and paper is output with half of the image printed on large sized paper. Therefore, it is corrected.
Page 1 of 4

Compatible Models: Kyocera-DF-730.
– Kyocera-DF-730 Service-Bulletin: is a handbook published by Kyocera manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Kyocera-DF-730 Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Kyocera-DF-730 Service-Bulletin:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Kyocera-DF-730 Service-Bulletin.
1.3 Diagnostic all errors are generated by Kyocera-DF-730 Service-Bulletin:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Kyocera-DF-730.
1.5 How to update firmware Kyocera-DF-730.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Kyocera-DF-730: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Kyocera-DF-730.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Kyocera-DF-730 Service-Bulletin covers following topics:

– Precautions Kyocera-DF-730.
– Product Specification Kyocera-DF-730.
– System Overview Kyocera-DF-730.
– S/W Structure and Descriptions Kyocera-DF-730.
– Disassembly and Reassembly Kyocera-DF-730.
– Alignment and Adjustments Kyocera-DF-730.
– Troubleshooting Kyocera-DF-730.
– Exploded Views & Parts List Kyocera-DF-730.

Free Download Kyocera-DF-730 Service-Bulletin

Kyocera-DF-730 Service-Bulletin

Leave a Reply