Service-Bulletin-Kyocera-DF-670

Service Bulletin KMIS Service Department, Kyocera Mita Europe 8270 / SB 2JB-004 Page of SB Number: SB 2JB-004 Creation Date: 17/04/2008 Subject: Model: Firmware upgrade (DF-670 and Bypass feeding issues) KM-2540/3040 Field measure No particular problems are expected. Please upgrade the firmware to the latest version whenever necessary. Latest firm - ware as of October 2007 Type MAIN ENGINE LANGUAGE E Program No. 2JB_2000002002 2JB_1000003001 2JB_81XE001003 Check SUM Version 84E2 7D06 6FB3 Status Date 002.002 003.001 001.003 Affected serial numbers Type KM-2540/3040 Serial number From the production of October 2007 Contents of changes Item Contents 1 The productivity of the DF-670 using the mixed sized originals mode has been improved. When mixed size original mode and sort mode is used each paper is sent separately to the finisher. The firmware has been changed so that equally sized paper is output as a set. 2 Correcting unnecessary print delay using the DF-670 in duplex mode. Added maintenance mode U944 (Initialize accounting data). The stop time for the last paper at the duplex switch back section is not necessary, so it has been deleted. 3 Currently U020 (All data initialize) has to be executed to initialize accounting data, this though also initializes other data. Maintenance mode U944 has been added to initialize accounting data exclusively. When FRPO command D6 is set to 01 (set the retry timing when the paper reaches the fuser unit), could cause the machine not to stop “driving” when a paper jam occurs. 4 Prevent machine from “driving” when paper Jam occurs after setting FRPO command D6 to 01. Incorrect detection of A5 paper as A4R, machine does not stop driving. 5 When A5 landscape is placed on the bypass tray and automatic paper size detection is set the paper is detected as A4R.
Page 1 of 1

Compatible Models: Kyocera-DF-670.
– Kyocera-DF-670 Service-Bulletin: is a handbook published by Kyocera manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Kyocera-DF-670 Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Kyocera-DF-670 Service-Bulletin:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Kyocera-DF-670 Service-Bulletin.
1.3 Diagnostic all errors are generated by Kyocera-DF-670 Service-Bulletin:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Kyocera-DF-670.
1.5 How to update firmware Kyocera-DF-670.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Kyocera-DF-670: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Kyocera-DF-670.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Kyocera-DF-670 Service-Bulletin covers following topics:

– Precautions Kyocera-DF-670.
– Product Specification Kyocera-DF-670.
– System Overview Kyocera-DF-670.
– S/W Structure and Descriptions Kyocera-DF-670.
– Disassembly and Reassembly Kyocera-DF-670.
– Alignment and Adjustments Kyocera-DF-670.
– Troubleshooting Kyocera-DF-670.
– Exploded Views & Parts List Kyocera-DF-670.

Free Download Kyocera-DF-670 Service-Bulletin

Kyocera-DF-670 Service-Bulletin

Leave a Reply