Service-Bulletin-Kyocera-DF-35

KMIS Service Team, Kyocera Mita Europe B.V. 5335 / SB AS-100 Service Bulletin 1 / 2 SB Number: SB AS-100 Subject: Model: Incorrect installment of decurler at ejection area (Attention points) DF-35 (Finisher for KM-C830 / KM-C830D) Issue Date: 27/04/2002 P HENOMENON The decurler rollers for the DF-35 at the ejection area are reversed, causing an increase in paper curl rather than a reduction. The metal roller, instead of the sponge roller, is in the upward position. F IELD M EASURE IMPORTANT Please make sure to re-install the sponge roller and metal roller as in Fig. 2 , at DF-35 setup or during your next field maintenance visit. Pay careful attention to the affected machine serial numbers on page 2 of this bulletin to determine whether or not the rollers have been incorrectly installed in your machine. Ejection unit of DF-35 Fig. 1. Reverse, incorrect installation of rollers Sponge roller Metal roller Fig. 2. Correct installation of rollers Sponge roller Metal roller WRONG CORRECT If the rollers were incorrectly installed ( Fig. 1 ), the paper may come out of the ejection section with a severe paper curl, especially when colour copying with an original including pictures on the entire image area. As a result, the paper may jam in the middle tray or the paper may be stocked incorrectly in the paper eject tray. F F
Page 1 of 12

Compatible Models: Kyocera-DF-35.
– Kyocera-DF-35 Service-Bulletin: is a handbook published by Kyocera manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Kyocera-DF-35 Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Kyocera-DF-35 Service-Bulletin:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Kyocera-DF-35 Service-Bulletin.
1.3 Diagnostic all errors are generated by Kyocera-DF-35 Service-Bulletin:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Kyocera-DF-35.
1.5 How to update firmware Kyocera-DF-35.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Kyocera-DF-35: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Kyocera-DF-35.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Kyocera-DF-35 Service-Bulletin covers following topics:

– Precautions Kyocera-DF-35.
– Product Specification Kyocera-DF-35.
– System Overview Kyocera-DF-35.
– S/W Structure and Descriptions Kyocera-DF-35.
– Disassembly and Reassembly Kyocera-DF-35.
– Alignment and Adjustments Kyocera-DF-35.
– Troubleshooting Kyocera-DF-35.
– Exploded Views & Parts List Kyocera-DF-35.

Free Download Kyocera-DF-35 Service-Bulletin

Kyocera-DF-35 Service-Bulletin

Leave a Reply