Service-Bulletin-Kyocera-B-2MV-0013-D069

Service Bulletin [Service Information] Subject Notes When Refitting the Drive Unit (Prevention of the Abnormal Noise from the Intermediate Transfer Belt Unit) TASKalfa 2550ci, FS-C8525MFP, FS-C8520MFP, FS-C8025MFP, FS-C8020MFP (Page.1/2) Ref. No. 2MV-0013 (D069) <Date> April 18, 2013 KYOCERA Document Solutions Europe Customer Services & Support Division (CSSD) Model [Notes] When refitting the drive unit, please make sure to insert the following shaft (X in the figure) into the cam of the drive unit, and then fix the drive unit. Afterwards, please check if the shaft (X) is inserted in the gear on the machine front side. [Phenomenon when the shaft ( X ) comes off] If the shaft ( X ) comes off, some abnormal noise from the intermediate transfer unit might be recognized or toner might leak from the retainer section. (Please refer to the next page for more details on the mechanism.) [Procedures how to refit the drive unit] 1 2 3 Refit the drive unit (*). * DR-895 (302K09312_) Remove the left lower cover, the main PWB and the intermediate transfer unit to insert the shaft ( X ) into the cam of the drive unit from the aperture of the metal plate behind the main PWB. Insert the shaft ( X ) into the cam of the drive unit. (Note) At this time, check if the front end of the shaft ( X ) is inserted in the gear on the machine front side. Machine inside Joint part with the shaft Cam of the drive unit Shaft ( X ) (Machine front side) (Machine rear side) Gear Drive unit Left lower cover Main PWB Correct Wrong The shaft ( X ) is inserted in the cam of the drive unit. Machine rear side The shaft ( X ) comes off from the cam of the drive unit. Shaft ( X ) Retainer section Cam Cam Shaft ( X ) Machine rear side
Page 1 of 2

Compatible Models: Kyocera-B-2MV-0013-D069.
– Kyocera-B-2MV-0013-D069 Service-Bulletin: is a handbook published by Kyocera manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Kyocera-B-2MV-0013-D069 Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Kyocera-B-2MV-0013-D069 Service-Bulletin:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Kyocera-B-2MV-0013-D069 Service-Bulletin.
1.3 Diagnostic all errors are generated by Kyocera-B-2MV-0013-D069 Service-Bulletin:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Kyocera-B-2MV-0013-D069.
1.5 How to update firmware Kyocera-B-2MV-0013-D069.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Kyocera-B-2MV-0013-D069: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Kyocera-B-2MV-0013-D069.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Kyocera-B-2MV-0013-D069 Service-Bulletin covers following topics:

– Precautions Kyocera-B-2MV-0013-D069.
– Product Specification Kyocera-B-2MV-0013-D069.
– System Overview Kyocera-B-2MV-0013-D069.
– S/W Structure and Descriptions Kyocera-B-2MV-0013-D069.
– Disassembly and Reassembly Kyocera-B-2MV-0013-D069.
– Alignment and Adjustments Kyocera-B-2MV-0013-D069.
– Troubleshooting Kyocera-B-2MV-0013-D069.
– Exploded Views & Parts List Kyocera-B-2MV-0013-D069.

Free Download Kyocera-B-2MV-0013-D069 Service-Bulletin

Kyocera-B-2MV-0013-D069 Service-Bulletin

Leave a Reply