Service-Bulletin-Kyocera-6500-8000

(TCSD-Revised Issue 1) Service Bulletin [Service Information] Subject Measures Against Fuser Belt Edge Tear TASKalfa 6500i / 8000i, TASKalfa 6550ci / 7550ci TASKalfa (Page.1/19) Ref. No. 2LF-0016 (C290) <Date> January 03, 2013 KYOCERA Document Solutions Europe Technical Customer Service Division (TCSD) Model KD C’s Classification Entire Stock Rework In-Field modification by case In-Field modification at next visit No modification necessary Topic The corrective measures against the fuser belt edge tear were informed by the previous Service Bulletin below (*). However, the corrective measures described in this Service Bulletin are no more required since the adjustment method at the production line has been changed to more precise since April 2012. Therefore, please execute the field measures by using following the flow chart. (*) Corrective measures 1: SB-2LF-0003-B345: New FILM FUSER ADJUSTS (302K902C30) added to the PLATE FUSER JOINT No ( A or later) Yes No Machine serial number is less than A ? Yes (Less than A ) Was the fuser belt edge torn before? Adjust MOUNT FUSER JOINT using the jig. Check Serial Number A of the main unit. Finish Adjust MOUNT FUSER JOINT using the jig. Finish Flange key gets under the U-shape groove of the heat roller or is raised. Yes No The fuser belt edge is torn. Is the fuser belt edge repeatedly torn after adjustment? Yes Apply the fuser unit with “ 5 or later as the last digit of the part code. Apply the fuser unit with “ 5 or later as the last digit of the part code. Apply the fuser unit with “ 5 or later as the last digit of the part code. Check the amount of the fuser belt shift. Finish No No Yes Is the fuser belt shifted by max. 0.3 mm ? Check the amount of the fuser belt shift. No Yes Is the fuser belt shifted by max. 0.3 mm after 10 sec. of belt rotation ? Is the fuser belt edge repeated- ly torn after adjustment? Finish Yes No
Page 1 of 19

Compatible Models: Kyocera-6500-8000.
– Kyocera-6500-8000 Service-Bulletin: is a handbook published by Kyocera manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Kyocera-6500-8000 Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Kyocera-6500-8000 Service-Bulletin:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Kyocera-6500-8000 Service-Bulletin.
1.3 Diagnostic all errors are generated by Kyocera-6500-8000 Service-Bulletin:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Kyocera-6500-8000.
1.5 How to update firmware Kyocera-6500-8000.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Kyocera-6500-8000: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Kyocera-6500-8000.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Kyocera-6500-8000 Service-Bulletin covers following topics:

– Precautions Kyocera-6500-8000.
– Product Specification Kyocera-6500-8000.
– System Overview Kyocera-6500-8000.
– S/W Structure and Descriptions Kyocera-6500-8000.
– Disassembly and Reassembly Kyocera-6500-8000.
– Alignment and Adjustments Kyocera-6500-8000.
– Troubleshooting Kyocera-6500-8000.
– Exploded Views & Parts List Kyocera-6500-8000.

Free Download Kyocera-6500-8000 Service-Bulletin

Kyocera-6500-8000 Service-Bulletin

Leave a Reply