Repair-Guide-Ricoh-FW-870

IMPORTANT SAFETY NOTICES PREVENTION OF PHYSICAL INJURY 1. Before disassembling or assembling parts of the copier and peripherals, make sure that the copier power cord is unplugged. 2. The wall outlet should be near the copier and easily accessible. 3. Note that some components of the copier and the paper tray unit are supplied with electrical voltage even if the main switch is turned off. 4. If any adjustment or operation check has to be made with exterior covers off or open while the main switch is turned on, keep hands away from electrified or mechanically driven components. 5. The inside and the metal parts of the fusing unit become extremely hot while the copier is operating. Be careful to avoid touching those components with your bare hands. 6.The copier is not attached to the table. Pushing the copier too heard may cause it to drop onto the floor. While moving the copier, push the table. 7. When the main switch is tuned on, the machine will suddenly start turning to perform the developer initialization. Keep hans away from any mechanical and electrical components during this period. HEALTH SAFETY CONDITIONS 1. Never operate the copier without the ozone filters installed. 2. Always replace the ozone filters with the specified ones at the specified intervals. 3. Toner and developer are non-toxic, but if you get either of them in your eyes by accident, it may cause temporary eye discomfort. Try to remove with eye drops or flush with water as first aid. If unsuccessful, get medical attention. OBSERVANCE OF ELECTRICAL SAFETY STANDARDS 1. The copier and its peripherals must be installed and maintained by a customer service representative who has completed the training course on those models. CAUTION 2. The RAM board on the main control board has a lithium battery which can explode if replaced incorrectly. Replace the RAM board only with an identical one. The manufacturer recommends replacing the entire RAM board. Do not recharge or burn this battery. Used RAM board must be handled in accordance with local regulations.
Page 1 of 206

Compatible Models: Ricoh-FW-870.
– Ricoh-FW-870 Repair-Guide: is a handbook published by Ricoh manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Ricoh-FW-870 Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Ricoh-FW-870 Repair-Guide:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Ricoh-FW-870 Repair-Guide.
1.3 Diagnostic all errors are generated by Ricoh-FW-870 Repair-Guide:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Ricoh-FW-870.
1.5 How to update firmware Ricoh-FW-870.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Ricoh-FW-870: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Ricoh-FW-870.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Ricoh-FW-870 Repair-Guide covers following topics:

– Precautions Ricoh-FW-870.
– Product Specification Ricoh-FW-870.
– System Overview Ricoh-FW-870.
– S/W Structure and Descriptions Ricoh-FW-870.
– Disassembly and Reassembly Ricoh-FW-870.
– Alignment and Adjustments Ricoh-FW-870.
– Troubleshooting Ricoh-FW-870.
– Exploded Views & Parts List Ricoh-FW-870.

Free Download Ricoh-FW-870 Repair-Guide

Ricoh-FW-870 Repair-Guide

Leave a Reply