i SAFETY INFORMATION All Areas INTERNAL LASER RADIATION Maximum radiation power: 8.8 x 10 -4 (W) Wavelength: 770-810 nm This is a Class IIIb Laser Diode Assy. that has an invisible Laser Beam. The Print Head Unit is NOT A FIELD SERVICE ITEM. Therefore, the Print Head Unit should not be opened under any circumstances. U.S.A. Only LASER SAFETY This LBP printer is certified as a Class 1 laser product under the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard according to the Food, Drug and Cosmetic Act of 1990. This means that the LBP printer does not produce hazardous laser radiation. Since radiation emitted inside the LBP printer is completely confined within protective housing and external covers, the laser beam cannot escape from the LBP printer during any phase of user operation. CDRH REGULATIONS The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration implemented regulations for laser products on August 2, 1976. These regulations apply to laser products manufactured from August 1, 1976. Compliance is mandatory for products marketed in the United States. The label shown in the figure indicates compliance with the CDRH regulations and must be attached to laser products marketed in the United States. CLASSIFICATION OF THE LASER PRODUCT This product is classified as a Class 1 Laser Product under the CDRH Regulations U.S.A. For other Countries Users WARNING : Use of controls, adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure. This is a semiconductor laser. The maximum power of the laser diode is 8.8 x 10 -4 W and the wavelength is 770-810 nm. For Denmark Users ADVARSEL : Usynlig laserstråling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsttelse for stråling. Klasse 1 laser produkt der opfylder IEC825 sikkerheds kravene. SAFETY INFORMATION
Page 1 of 87

Compatible Models: Konica-2060-Pagework-20.
– Konica-2060-Pagework-20 Repair-Guide: is a handbook published by Konica manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Konica-2060-Pagework-20 Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Konica-2060-Pagework-20 Repair-Guide:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Konica-2060-Pagework-20 Repair-Guide.
1.3 Diagnostic all errors are generated by Konica-2060-Pagework-20 Repair-Guide:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Konica-2060-Pagework-20.
1.5 How to update firmware Konica-2060-Pagework-20.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Konica-2060-Pagework-20: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Konica-2060-Pagework-20.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Konica-2060-Pagework-20 Repair-Guide covers following topics:

– Precautions Konica-2060-Pagework-20.
– Product Specification Konica-2060-Pagework-20.
– System Overview Konica-2060-Pagework-20.
– S/W Structure and Descriptions Konica-2060-Pagework-20.
– Disassembly and Reassembly Konica-2060-Pagework-20.
– Alignment and Adjustments Konica-2060-Pagework-20.
– Troubleshooting Konica-2060-Pagework-20.
– Exploded Views & Parts List Konica-2060-Pagework-20.

Free Download Konica-2060-Pagework-20 Repair-Guide

Konica-2060-Pagework-20 Repair-Guide

Leave a Reply