Installation-Guide-Kyocera-PrintSysZ

1 1 A B A 2009.2 303MY56710 Printing System(X)安装手册 設置手順書 Printing System (X) English INSTALLATION GUIDE FOR THE Printing System (Z) Français GUIDE D’INSTALLATION DU Printing System (Z) 日本語 简体中文 Español GUIA DE INSTALACION PARA EL Printing System (Z) Deutsch INSTALLATIONSANLEITUNG FUR Printing System (Z) Italiano GUIDA ALL’INSTALLAZIONE PEL Printing System (Z) 同梱品 A プリンタボード......................1 オプション B USB インタフェース IB-110 ...........1 プリンタボードの取り付け 1. ビス(1) 本を外し、カバー(2)を取り外す。 附属品 A 打印板..............................1 选购件 B USB 接口 IB-110 .....................1 安装打印板 1. 卸下 2 颗螺钉 (1),然后卸下盖板 (2)。 Supplied part A Printer board ........................................... 1 Option B USB interface IB-110............................... 1 Installing the printer board 1. Remove two screws (1) and remove the cover (2). Contenu standard A Carte d’imprimante.................................. 1 Option B Interface USB IB-110............................... 1 Installation de la carte d’imprimante 1. Oter les deux vis (1) et retirer le couvercle (2). Índice general A Tarjeta de impresora................................ 1 Opción B Interfaz USB IB-110................................. 1 Instalación de la tarjeta de impresora 1. Quite los dos tornillos (1) y desmonte la cubierta (2). Lieferumfang (Standard) A Druckerkarte............................................ 1 Option B USB-Schnittstelle IB-110 ......................... 1 Installieren der Druckerkarte 1. Die zwei Schrauben (1) herausdrehen, und die Abdeckung (2) abnehmen. Dotazione standard A Scheda stampante................................... 1 Opzione B Interfaccia USB IB-110 ........................... 1 Montaggio della scheda stampante 1. Rimuovere le due viti (1) per togliere il pannello (2). 同梱品に固定テープ、緩衝材が付いている場合は 必ず取り外すこと。 取り付け作業を行う前には、必ず複写機本体の主 電源スイッチを OFF にし、電源プラグを抜いてか ら作業すること。 如果附属品上带有固定胶带、缓冲材料时务必揭 下。 在安装作业之前,必须切断 (OFF) 复印机主机的电 源开关,并拔下电源插头后再进行操作。 Be sure to remove any tape and/or cushioning material from supplied parts. Before installing the printing system, turn the copier’s power switch OFF and unplug the copier from the power supply. Veillez à retirer les morceaux de bande adhésive et/ou les matériaux de rembourrage des pièces fournies. Avant d’installer le système d’impression, mettre le copieur hors tension à l’interrupteur principal et le débrancher de la prise secteur. Asegúrese de despegar todas las cintas y/o material amortiguador de las partes suministradas. Antes de instalar el sistema de impresión, apague la fotocopiadora a OFF y desenchufe la fotocopiadora del suministro eléctrico. Entfernen Sie Klebeband und/oder Dämpfungsmaterial vollständig von den mitgelieferten Teilen. Bevor Sie das Drucksystem installieren, schalten Sie den Netzschalter des Kopierers aus, und trennen Sie den Kopierer vom Stromnetz. Accertarsi di rimuovere tutti i nastri adesivi e/o il materiale di imbottitura dalle parti fornite. Prima di eseguire il montaggio del sistema di stampa, spegnere l’interruttore principale e sfilare la spina della copiatrice dalla presa. 1 1 2 2. プリンタボード(A)を奥まで挿入し、手順 1 で取り外したビス(1) 本で固 定する。 2. 将打印板 (A) 插入到底,用步骤 1 卸下的 2 颗螺钉 (1) 加以固定。 2. Insert the printer board (A) all the way into the slot and secure it with two screws (1) that have been removed in step 1. 2. Insérer la carte d’imprimante (A) à fond dans la fente et la fixer à l’aide de deux vis (1) qui avaient été retirées auparavant à l’étape 1. 2. Inserte la tarjeta de impresora (A) completamente en la ranura y asegure con los tornillos (1) quitados en el paso 1. 2. Die Druckerkarte (A) bis zum Anschlag in den Steckplatz einschieben und mit den in Schritt 1 entfernten zwei Schrauben (1) befestigen. 2. Inserire la scheda stampante (A) fino in fondo nello slot e fissarla con le due viti (1) che sono state rimosse nel passo 1.
Page 1 of 2

Compatible Models: Kyocera-PrintSysZ.
– Kyocera-PrintSysZ Installation-Guide: is a handbook published by Kyocera manufacturer or a specialized publishing company that contains instructions and specifications for the maintenance, repair, and how to fix all error of a specific Kyocera-PrintSysZ Printer. It may includes Exploded Views, Parts List, System Diagram, Disassembly and Reassembly, Alignment, Troubleshooting guides, Adjustments, hard reset code, factory reset…

You can do with Kyocera-PrintSysZ Installation-Guide:

1.1 Guide you from basic to advanced usage it.
1.2 Fluent Disassembly and Re-assembly Kyocera-PrintSysZ Installation-Guide.
1.3 Diagnostic all errors are generated by Kyocera-PrintSysZ Installation-Guide:
– The printer does not print.
– Paper does not feed into the printer.
– A print job is extremely slow.
– Half the page is blank.
– The paper keeps jamming, Paper Jam inside, Paper Jam Outside…
– The printer prints, but the text is wrong, garbled, or incomplete.
– Pages print, but are blank.
– The print quality of photos is not good. Images are not clear.
– Your printer has an odd smell during initial use.
1.4 How to refill toner/ink Kyocera-PrintSysZ.
1.5 How to update firmware Kyocera-PrintSysZ.
1.6 How to reset page counter by software, fix all error cause by ink/toner cartridge Kyocera-PrintSysZ: Waste Ink Ink Pad Error, ink cartridge error, red light blinking, red-green light blinking, yellow blinking, Ink cartridge failure, waste ink over flow, ink out, ink level, incompatible ink cartridges, toner cartridge not competition, install toner cartridge, toner exhausted, toner low, toner empty, toner very low…How to use Adjustments Program.
1.7 How to fix main board error, print head, formater board error Kyocera-PrintSysZ.
1.8 How to troubleshooting printer problem with low quality page .
1.9 How to fix : Communication Error, Model Difference, Cover open(Tray) Error, Paper Out Error, Paper Jam Error, Paper Mismatch Error, Ink Low, Ink End Error, No Ink Cartridge, CSIC Error, Maintenance Request Error, Fatal Error…
1.10 How to fix sensor error: empty image, imaging unit is not installed, sensor failure, turn off then on, fusser error, LSU error, Engine board problem, Flash ROM problem, Main motor problem, Sirocco fan problem, Power supply cooling fan problem, Suction fan problem, Polygon motor problem, Laser problem, Secondary transfer voltage contact/release problem, Transfer belt cleaner contact/release problem, Transfer belt rotation problem, Imaging rack rotation problem, Fuser roller temperature increase problem, Fuser roller low temperature problem, Fuser roller high temperature problem, Fuser roller thermistor problem, Transparency detection sensor problem, Main unit memory counter problem, Main unit memory data problem, Main unit memory access problem, Main unit memory installation problem, Engine communication error.

Kyocera-PrintSysZ Installation-Guide covers following topics:

– Precautions Kyocera-PrintSysZ.
– Product Specification Kyocera-PrintSysZ.
– System Overview Kyocera-PrintSysZ.
– S/W Structure and Descriptions Kyocera-PrintSysZ.
– Disassembly and Reassembly Kyocera-PrintSysZ.
– Alignment and Adjustments Kyocera-PrintSysZ.
– Troubleshooting Kyocera-PrintSysZ.
– Exploded Views & Parts List Kyocera-PrintSysZ.

Free Download Kyocera-PrintSysZ Installation-Guide

Kyocera-PrintSysZ Installation-Guide

Leave a Reply